Hook up bush hog, hq fresh hogtied xxx films
Industry News – From Chicagolands Equipment Experts
Page 35 Because a closed-center system requires no flow of oil through the backhoe control valve when the levers are in a neutral position, the backhoe must not be connected to a closed-center tractor hydraulic system. Page 33 There have been several different valves used on the loader in past years.
Page 27 Mounting Backhoe to Tractor or Skid Steer loaders The Bush Hog backhoe can be mounted to the power source using three different attaching kits. A PTO pump kit is required if the tractor is to be mounted to a tractor with closed-center hydraulic system.
You may need to return to Step 6 and readjust upward or downward the bolt connection. Tighten all hardware to the torque requirements specified in the torque chart.
The open-center system con- stantly pumps oil through the hydraulic cylinder operat- ing valves and returns the oil to the reservoir.
The power beyond plug is included with the loader valve when the valve is ordered. For removal and storage, follow these steps: The closed-center system does not pump oil until there is a demand for oil from one of the hydraulic cylinders.
The second is also used to operate the backhoe and loader off the backhoe PTO pump kit option. See figure 11 for parts involved in the make- up of the spool control kit.
Additional hydraulic components or kits will be required to complete the hook-up to the tractor hydraulic system.
However, foot pad kits are available as options. These kits bolt to the standard feet and increase the versatility of the backhoe. Install the swing safety lock pin as shown in Figures 1 and 3.
The 3-point hitch kit is the 6. Failure to do so may result in backhoe being thrust upward, crushing operator against cab or ROPS.
A set of stabilizer arms is included. Hydraulic Hook-up Figure 16 Backhoe Mainframe They bolt from the adjustable upper link to the backhoe mainframe, locking the hoe rigidly in one position.
Seen and Heard
Tighten all hardware to the torque requirements specified in the torque chart. Thoroughly clean the exterior of the Hook up bush hog before beginning disassembly procedures.
They are suitable for most backhoe work and generally are all that is ever required.
Page 21 Troubleshooting Continued Problem Loss of power in any one cylinder, including lift and crowd Loss of power in swing cylinders, but other cylinders functioning properly. The open-center system con- stantly pumps oil through the hydraulic cylinder operat- ing valves and returns the oil to the reservoir.
If the fittings or plugs cannot be located, they can be obtained from Bush Hog Service Parts. They bolt from the adjustable upper link to the backhoe mainframe, locking the hoe rigid- ly in one position.
Page 24 Troubleshooting Continued Problem Unable to push valve spool in Spring centered spools do not return to neutral Cause Paint on valve spool; sticking valve spool or scored valve spool Oil leakage past spool seal into spool cap Bent spool Foreign particles Misalignment of control handle linkage Paint on valve spool; Keep parts in order of disas- sembly.
Maximum swing action cannot be obtained Slow operation of Herpes and you dating lack of power all cylinders Cause Worn or damaged rod seals on cylinder; Page 23 Troubleshooting Continued Problem Leaky cylinders Leaky valve Sticky valve spool Cause Oil is bypassing cylinder piston, scored piston, worn piston packing, or defective piston assembly Scored piston rods and worn guides in cylinder Bent piston rod in cylinder Worn or damaged rod seals on cylinder; Tighten all hardware to the torque requirements specified in the torque chart on page The fittings required to con- vert the Bush Hog loader valve to a power beyond application are included in the loader valve kit.
They include the PTO pump 6 or 8 gpm and adapter, reservoir, filtration system, hydraulic hoses, and fittings. A PTO pump kit is required if the backhoe is to be mounted to a tractor with a closed-center hydraulic system.
Remove control valve from the backhoe. The closed-center system does not pump oil until there is a demand for oil from one of the hydraulic cylinders.